Product ID:V-VANADIUM PERMENDUR, TAPE WOUND & BOBBIN (
MSDS Date:01/05/1987
FSC:9650
NIIN:00N030409
MSDS Number: BNMWX

ARNOLD ENGINEERING CO

300 WEST ST
MARENGO, IL 60152
US

Emergency Phone: 815-568-2303

Info Phone: 815-568-2303

Preparer: K.L.LATIMER

Cage: 95566

ARNOLD ENGINEERING CO DIV OF SPS TECHNOLOGIES

G MARENGO, IL 60152 US

Telephone: 815-568-2000

Cage: 95566

NICKEL (SARA III)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 48%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3

VANADIUM PENTOXIDE (FUME); (VANADIUM) (SARA III). OSHA

CAS: 1314-62-1

RTECS: YW2460000

Fraction By Weight: 2%

OSHA PEL C,0.5 MG/M3

ACGIH TLV: 0.05 MG/M3RDUST;9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

IRON

CAS: 7439-89-6

RTECS: NO4565500

Fraction By Weight: BALANCE

OSHA PEL 10 MG/M3

ACGIH TLV: 5 MG/M3

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:ANY LONG-TERM EXPOSURE TO DUSTS
EXCEEDING RECOMMENDED TLV LEVELS MAY RESULT IN IRRITATION TO UPPER
RESPIRATORY TRACT. DUSTS IN EYES MAY CAUSE IRRITATION. PROLONGED
SKIN CONTACT W/NICKEL MAY CAUSE ALLE RGIC REACTION IN SENSITIVE
INDIVIDUALS.AVOID INGESTION OF DUSTS BY NOT EATING, DRINKING, OR
SMOKING (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL:GROUP 2 (NTP), GROUP 1 (IARC).
Effects of Overexposure:HLTH HAZ:IN AREAS WHERE DUSTS OR FUMES ARE
GENERATED.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INHAL:REMOVE TO FRESH AIR. SUPPORT BRTHG (GIVE O2/ARTF RESP),
CALL MD . EYE:FLUSH W/WATER FOR AT LEAST 15 MINUTES. SKIN:FLUSH
W/COPIOUS AMOUNTS OF WATER, CALL MD . INGEST:GET MD IMMEDIATEL Y .

Extinguishing Media:USE MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:PROD NOT COMBUSTIBLE. BUT IF ADDTNL
GRINDING/MACHINING PERFORMED, SHOULD BE DONE USING COOLANTS TO
CONTROL DUST LEVELS. FINE METAL PWDRS MAY CAUSE EXPLO HAZ.

Spill Release Procedures:DUSTS MAY BE SWEPT WET OR VACUUMED TO KEEP
AIRBORNE DUST CONCENTRATIONS TO A MINIMUM.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:USE GOOD MANUFACTURING PRACTICES &
GOOD HOUSEKEEPING PRACTICES THAT WILL KEEP GENERATED DUSTS TO A
MINIMUM.
Other Precautions:GRINDING OR MACHINING OPERATIONS SHOULD BE PERFORMED
USING COOLANTS TO REDUCE DUSTS.

Respiratory Protection:IF AIRBORNE CONCENTRATIONS EXCEED THOSE
SPECIFIED, A NIOSH/MSHA APPROVED RESPIRATOR SHOULD BE USED.
Ventilation:ADEQUATE LOCAL VENTILATION SHOULD BE USED WHEN DRY
GRINDING/ MACHINING ALLOYS TO KEEP EXPOSURE LEVELS BELOW RECOMM
TLV.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:USE PERSONAL PROTECTION EQUIPMENT WHEN
REQUIRED.
Work Hygienic Practices:USE GOOD PERSONAL HYGIENE PRACTICES.
Supplemental Safety and Health
MFR'S TRADE NAME/PART NO:CORES USING NICKEL- IRON ALLOY.

HCC:N1
Spec Gravity:8.18
Solubility in Water:NOT SOLUBLE
Appearance and Odor:DARK BLUE TO BLACK. NO ODOR.

Stability Indicator/Materials to Avoid:YES
POWDERS/DUSTS FROM PRODUCT INCOMPATIBLE W/STRONG OXIDIZING AGENTS SUCH
AS NITRIC ACID.
Stability Condition to Avoid:AVOID GENERATION OF AIRBORNE DUSTS.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

Waste Disposal Methods:DISPOSE I/A/W FEDERAL, STATE AND LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.